The "small cuts" all over the anti-corrosion sleepers are not made in vain
Release Date: 2026-11-18 Visits: 5


When the older generation sewed the soles of shoes, they would first use an awl to prick a row of holes before starting. The needle and thread followed these holes, with one stitch per step, to make the sole densely sewn. If they used a needle to prick directly, the thread would go crooked and it would be strenuous for the hands. The anti-corrosion sleepers used on the railway also have such rows of small cuts on them. These cuts are made by scratching, and have nothing to do with bumps. They are all over the body, and none of them are made in vain.

When this piece of wood arrived at the factory, it was a pine log. After the bark was peeled off, it was sawn into a neat square piece. The freshly sawn wood was light in color and felt light in the hand. Holding a handful of sawdust, one could still smell the fresh wood scent. It was spread out in a ventilated place and dried for a while. With a cushion underneath, air could flow through the gaps, making both the inside and outside of the wood loosen. Only then did the next step of making cuts come into play. At this point, it was still white and smooth, with no hint of what it would become in the future. There were still some burrs left from the saw cuts when touched.

To fully impregnate the entire piece with preservative oil, it relies on these fine openings throughout the body. If one side is not scratched enough, that side will be less impregnated, resulting in uneven depth across the entire piece. Row by row, the spacing looks almost the same, and only then can the work under hand be considered neat. After going through one round, the master has to turn back and take a glance to see if any section is missed. If a section is missed, it has to be re-impregnated. This job never stops.

What exactly are these small cuts for? Pine wood has a fine and dense texture. If the oil is only rubbed in slowly from the outside, it will run out halfway, and although the surface looks moist, the inside remains dry. Once the cuts are made, the oil has a guide to follow, and it will travel along these fine paths to reach its intended destination. The cuts must be made closely and evenly for the oil to spread evenly. Every cut counts, and none is wasted. The same principle applies to watering crops in the fields. First, shallow trenches are dug in the ground, so that water can flow along the trenches to the roots. If water is poured directly, the surrounding soil will remain dry. These cuts on the wood serve the same purpose as digging trenches. When the water flows evenly, the vegetables in the same plot will grow evenly. The trenches must be dug evenly for the water to flow evenly. The cuts must be made evenly for the oil to spread evenly.

The material is pushed into the tank, and as soon as the door is closed, the gas inside the tank gives way. The empty space is vacated, and the oil warms up, flowing along the fine channels all over the body and into the depths. Outside, more effort is gradually applied to send it deeper. The master observes which layer the oil reaches and whether it is evenly distributed. When it has reached enough, the remaining oil on the tank surface is collected, the tank relaxes, and the door opens. At this point, the material is uniform in color and feels moist to the touch. It cannot be immediately loaded onto the truck after leaving the tank; it needs to be left in the yard for a few more days to allow the oil to settle inside. Being in a hurry is useless; it will take its time and cannot be urged. This period of time cannot be saved, and the masters all know it in their hearts.

Looking back at those small cuts, from top to bottom and from front to back, one next to another, it's really hard to find which one is just for show. When grilling fish, it's necessary to make several diagonal cuts on the fish body. This isn't just for aesthetic purposes; the seasoning will penetrate along the cuts, ensuring the meat is flavorful. The cuts on the wood are all for the same purpose. They may seem unremarkable, but if any of them are missing, the oil in that area will not be evenly distributed. The entire piece of wood, from one end to the other, has the same depth, relying on these unremarkable cuts. This is precisely why the master is unwilling to save effort.

Once it's in place, it still performs its old job, supporting the steel rails. It's commonly seen under the small tracks used for hauling coal in the mine and the short rails in the freight yard. The material itself has some elasticity. When a heavy vehicle passes over it, it sinks slightly and then returns to its original shape, continuing to be used again and again. Its color can withstand being manipulated. Whether it's laid on an old or new track, it's impossible to tell the difference at a glance. The workers who do the work don't take special care of it either. They just lay it down and use it with peace of mind. If it needs to be replaced one day, they just lift it up, move it, re-drive the nails in, and continue using it. It doesn't care about these things. It's reliable no matter where it's laid.

So don't underestimate that small opening. Whether the oil can penetrate to the core is determined by this process.